Advantech ACP-4001 Instrukcja Użytkownika

iIACP-4000 Series5.7" VGA TFT LCD Pentium 4/ Celeron D 4U Industrial Workstation with 7xISA/PCI SlotsUsers Manual

IACP-4000 User Manual 41.3 IACP-4000 Series List• IACP-4000D-A0AE 5.7" VGA TFT LCD Pentium/Celeron D 4U Rack Industrial Workstation with5 PCI/

5 Chapter 1 1.5 Exploded DiagramFigure 1.1: Exploded Diagram1.6 Accessory Packing list• CABLE 6P-6P-6P PS/2 KB & MOUSE 20cm • Simplified Chin

IACP-4000 User Manual 6For IACP-4000D series only:• CABLE 6P/6P 20cm Mini DIN (M) for AWS-8421T• CABLE 15/15P 20cm for AWS-8259 VGA PortNote: This m

7 Chapter 2 CHAPTER 2System Setup

IACP-4000 User Manual 8Chapter 2 System Setup2.1 System Installation 2.1.1 Attaching the HandlesThe handles for the front panel are in the accessory

9 Chapter 2 2.1.3 Chassis Front and Rear SectionsThe front panel switches behind the door are used for system power, sys-tem reset 1, system reset 2

IACP-4000 User Manual 10System Reset 1: Press this switch to reinitialize the system. This is the same as the hardware reset button. (Default setting

11 Chapter 2 2.1.4 Drive Bay InstallationThe drive bay of IACP-4000 can hold 5.25" (x3) and 3.5" (x1) devices. Installation of disk drives

IACP-4000 User Manual 122.2 LED Indicators2.2.1 System Status LEDThe System Status LED shows as follows:When the PWR LED is RED, it indicates a redu

13 Chapter 2 2.2.2 Power Status LEDPower Status LED indicates the status of the backplane voltage signals.When a LED fails to light, it indicates a p

IACP-4000 User Manual iiCopyright This document is copyrighted, 20

IACP-4000 User Manual 142.4 Cooling Fan & FilterThere are two cooling fans located inside the chassis. When one cooling fan breaks down, the sy

15 Chapter 3 CHAPTER 3Alarm Board

IACP-4000 User Manual 16Chapter 3 Alarm BoardThe alarm board is located under the cooling fan section. It gives an audible alarm when:1. Any power

17 Chapter 3 3.2 Alarm Board SpecificationInput Power: +5V, +12VInput Signals:• 7 FAN connectors (GND_+12V_FAN)• One thermal board connector (up t

IACP-4000 User Manual 18CN1 : External Power Connector, standard mini 4 Pin power connectorPin 1 : +12V, 2A current maximum Pin 2 : GNDPin 3 : GND Pin

19 Chapter 3 Pin 1 : SIN Pin 2 : SOUTPin 3 : CTS# Pin 4 : DCD#Pin 5 : RTS# Pin 6 : DTR#Pin 7 : DSR# Pin 8 : ID 0Pin 9 : ATX ON Pin 10 : DO 4Pin 11 :

IACP-4000 User Manual 20Pin 1 : Power GOOD A Pin 2 : GNDCN18 : LED Board ConnectorPin 1 : GND Pin 2 : +5V SignalPin 3 : +12V Signal Pin 4 : -5V Si

21 Chapter 3 3.3 Switch SettingFan Number SettingThermal Board Temperature Setting

IACP-4000 User Manual 223.4 Thermal SensorThere is a temperature sensor inside the chassis, See Figure 3.4-1.to find the location.When the temperatu

iiiFCC Class ANote: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Ru

IACP-4000 User Manual ivSafety Instructions 1. Read these sa

vContentsChapter 1 General Information ... 21.1 Introduction ...

IACP-4000 User Manual vi

1 Chapter 1 CHAPTER1General Information

IACP-4000 User Manual 2Chapter 1 General Information1.1 IntroductionIACP-4000 is a 4U height 14-slot rackmount IPC chassis with ATX industrial mothe

3 Chapter 1 1.2.2 System Hardware• Audio Ports 1 x Mic-in, 1 x Line-out, 1 x CD Audio in, 1 x Line out, 1 x S/PDIF • Chipset Intel 82915GV GMCH• C