Advantech EKI-2548I Instrukcja Użytkownika

EKI-2548I 8-port 10/100TX Managed Ethernet Switch with Wide Operating Temperature User Manual

Chapter 1 Overview 1.1 Introduction To create reliability in your network, the EKI-2548I comes equipped with a proprietary redundant network prot

1.2 Features • Provides 8 x 10/100 Mbps Ethernet ports with RJ45 connector • Redundancy: X-Ring, Dual Homing, Couple Ring, IEEE802.1d STP & IE

1.3 Specifications Communications Standard IEEE 802.3, 802.3u, 802.3x IEEE 802.1d, 802.1p, 802.1Q, 802.1w LAN 10/100Base-TX Transmission Distanc

Environment Operating Temperature -40 ~ 75oC -40 ~ 60oC (non-air-flow environment) Operating Humidity 5 ~ 95% (non-condensing) Storage Temperatu

EKI-2548I_Manual_ed2 6 1.4 Packing List • 1 x EKI-2548I Industrial Managed Fast Ethernet Switch • 1 x eAut

7 Chapter2 Installation Sections include: z LED Indicators

Chapter 2 Installation In this chapter, you will be given an overview of the EKI-2548I hardware installation procedures. 2.1 LED Indicators The

2.2 DIP Switch The EKI-2548I Managed Industrial Switch provides a 9-pole DIP switch for configuring the relay alarm operation mode and the master ri

2.4 Dimensions (units: mm) 15259.6 Figure 2.4-1 Front View of EKI-2548I EKI-2548I_Manual_ed2 10

50 48.5 53.59.641.3 40 Figure 2.4-2 Side View of EKI-2548I 11 Chapter2

Copyright The documentation and the software included with this product are copyrighted 2010 by Advantech Co., Ltd. All rights are reserved. Advantec

15.29.6 Figure 2.4-3 Rear View of EKI-2548I EKI-2548I_Manual_ed2 12

114.62105 0.629 Figure 2.4-4 Top View of EKI-2548I 13 Chapter2

2.5 Mounting The EKI-2548I supports two mounting methods: DIN-rail & Wall mountings. 2.5.1 Wall Mounting EKI-2548I can be wall-mounted by usi

2.5.2 DIN-rail Mounting You can also mount EKI-2548I on a standard DIN-rail by following the steps below. The DIN-rail kit is screwed on the indust

Then, hook the device over the DIN rail and let it drop down straight to slide over the rail smoothly. Figure 2.5-3 Installation to DIN-rail Step

2.6 Wiring Power and P-Fail Contacts The EKI-2548I supports dual +12 ~ 48 VDC and 24 VAC power inputs, and P-Fail relay output. Terminal Blo

2.7 X-Ring Application The industrial switch supports the X-Ring protocol that can help the network system recover from network connection failure w

2.8 Coupling Ring Application As the illustration shown below, users can use the X-Ring groups to form a coupling ring for redundant backup. It can

2.9 Dual Homing Application The Dual Homing function is to prevent the connection loss between the particular X-Ring group and the upper level/core

21 Chapter3 Configuration

Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and wo

Chapter 3 Configuration 3.1 Web Browser EKI-2548I provides a convenient configuring way via web browser. You can follow the steps below to access

The default user name and password are both admin, fill in the user name and password then press OK to enter the configuration. You can change the pa

3.1.1 System Switch Settings This page displays system information and gives users the interface to assign the system name, location, system contac

IP Configuration Users can configure the IP Settings and DHCP client function here. • DHCP Client: Enable or disable the DHCP client function. Whe

TFTP - Update Firmware Trivial File Transfer Protocol (TFTP) is a very simple file transfer protocol with the functionality of a very basic form of

System Log – System Log Configuration Configure the system event mode to collect system log. • System Log Mode: Select the system log mode—Client O

System Log – Event Configuration • System event selection: There are 4 event types—Device cold start, Power status, SNMP Authentication Failure, an

SNTP Configuration You can configure the SNTP (Simple Network Time Protocol) settings which allow you to synchronize the switch clock with an Intern

ZP6 - USSR Zone 5 +6 hours 6 pm WAST - West Australian Standard +7 hours 7 pm CCT - China Coast, USSR Zone 7 +8 hours 8 pm JST - Japan Standard

IP Security The IP security function allows the user to assign 10 specific IP addresses that have permission to access the switch through the web br

Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipmen

Security Manager Change web management login user name and password for the management security issue. • User Name: Key in the new user name (The

Alert – Email Alert Configuration When the specific event occurs, the system will send the alert to the email account assigned by users. Users can a

Alert – Event Configuration The selected events that occur will cause the system to send out alerts to the assigned SMTP server. Also, users can sel

Alert – Power Alarm Configuration The power alarm configuration enables the Relay alarm. • Tick the check box and clickApply to have the configura

3.1.2 Port Port setting includes Port Status, Port Statistics, Port Control, Port Mirroring, and Rate Control. Through this interface, users can se

Port Statistics The following information provides the current port statistics. • Port: Displays the port number. • Type: Displays the media type

Port Control In Port Control, you can select ports and click the pull-down menus to set parameters of each port to control the transmitting/receivin

Port Mirroring The Port mirroring is a method to monitor traffic in switched networks. Traffic through ports can be monitored by one specific port.

Rate Control Here you can set up every port’s packet limitation type and bandwidth rate. • Limit Packet Type: Select the packet type you want to f

3.1.3 Protocol The user can configure the layer 2 protocol setting via this interface. VLAN configuration A Virtual LAN (VLAN) is a logical networ

Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment

VLAN configuration - Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated as belonging to

Figure 3.1-22 Port-based Mode--Add • Enter Group Name and VLAN ID. Having selected the port numbers, click Add to add the ports to the right fiel

• Select the VLAN group name and click Edit to modify group name, VLAN ID, or add/remove the members of the existing VLAN group. Note Remember to

802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different swi

Add Add an 802.1Q-based VLAN group. • Group Name: Specify the group name for the VLAN. • VLAN ID: Please enter the VLAN ID in the range of 2 to 409

Figure 3.1-26 Tag/Untag Member Ports Edit/Delete Modify or delete the existed VLAN groups. • Select an existed VLAN group from the list. • Clic

802.1Q Configuration – Port VLAN ID Assign the Port VLAN ID for the selected ports. • Port: Select ports to be assigned a Port VLAN ID. • Port VL

Rapid Spanning Tree The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree conv

RSTP - Port Configuration Here you can configure the path cost and priority of each port. • Select the port in the port column field. • Path Cost:

SNMP Configuration Simple Network Management Protocol (SNMP) is the protocol developed to manage nodes (servers, workstations, routers, switches and

Contents Chapter 1 Overview...2 1.1 Introduction ...

• Click Add. • To remove the community string, select the community string listed in the current managers field and click Remove. EKI-2548I_Manual

QoS Configuration Here you can configure Qos policy and priority setting, port priority setting, COS and TOS setting. QoS Policy • Qos Policy: S

Figure 3.1-31 QoS Configuration EKI-2548I_Manual_ed2 54

IGMP Configuration The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast t

X-Ring X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar to STP or RSTP, but the algorithms between the

Note To enable the X-Ring function, users must disable the RSTP first. The X-Ring function and RSTP function cannot both be activated on a single

3.1.4 Configuration Backup This interface allows users to back up the current configuration on the switch to the TFTP server. Also, users can restor

3.1.5 Factory Default Reset the switch to default configuration. Tick the check boxes to keep the current IP address, user name and password before

EKI-2548I_Manual_ed2 60

61 Appendix A Troubleshooting CHAPTER

Figure 3.1-7 System Log Configuration...27 Figure 3.1-8 Event Configuration...

Chapter 4 Troubleshooting Verify that you are using the right power cord/adapter. Don’t use the power adaptor with DC output voltage higher than t

63 Appendix A Pin Assignments & Wiring APPENDIX

Appendix A Pin Assignments & Wiring A.1 RJ-45 Port It is suggested to adopt ELA/TIA as the wiring of the RJ-45. Figure A.1: RJ-45 Pin A

MDI/MDI-X Pin Assignments Pin Number MDI-X Signal Name MDI Signal Name 1 Receive Data plus (RD+) Transmit Data plus (TD+) 2 Receive Data minus

viii

1 Chapter1 Overview Sections include: z Introduction z Fea