Advantech MIC-5332 Instrukcja Użytkownika Strona 60
- Strona / 129
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
3. Choose a proper connection (LAN, KCS, or IPMB) to the MIC-5332. Taking LAN
for example, connect theFront Panel IO GbE-LAN RJ-45 port (LAN1 or LAN2) to
the LAN port on a PC via an Ethernet cable.
4. Turn on the MIC-5332.
5. Use a command line on the remote PC, then move to the directory where IPMItool
is located.
6. IPMItool is ready for use now.
For Linux users:
1. Make sure the IPMI driver has been mounted. (The built-in IPMI driver in current
Linux kernel is compatible with MIC-5332)
2. Open the IPMItool folder. (CD path: \IPMItool\Linux)
3. Put “IPMItool” in a specific location on the terminal PC.
4. Follow the same procedure as Windows users from the above step 3~5.
5. IPMItool is ready for use now.
Before establishing the SoL session, the user needs to set related parameters such
as user name, password, and a static IP address of LAN interface via IPMItool. The
general IPMI command syntax is:
The example below shows access to the IPMC through LAN (RMCP), often referred
as IPMI-over-LAN. Using KCS or IPMB is similar.
Note: If you have any problem for setup, contact Advantech technical support team.
4.6.2.2 LAN Commands
To get an overview of all possible LAN commands, please use the keyword “lan” only.
If user wants to change the IP address to their need, please use the following
command:
IPMItool General Command Line Syntax:
ipmitool <connection-method> <ipmitool command>
<connection-method> The interface connected to the IPMC. User may
use LAN or IPMB remotely, or KCS locally
<ipmitool command> The command to be executed with the ipmitool
- Revision History 2
- Copyright 3
- Acknowledgements 3
- Product Warranty (2 years) 3
- Declaration of Conformity 4
- Warnings, Cautions and Notes 5
- Document Feedback 5
- Packing List 5
- Safety Instructions 6
- We Appreciate Your Input 6
- Glossary 8
- Chapter 1 10
- Product Overview 10
- 1.1 MIC-5332 Overview 11
- 1.2 Block Diagram 13
- 1.3 Product Configurations 14
- 1.4 Related Products 14
- Chapter 2 15
- Board Features 15
- 2.1 Technical Data 16
- 2.2 Product Features 17
- 2.2.3 DMI Gen2 18
- 2.2.5 Redundant BIOS Flash 19
- 2.3 DDR3 DIMMs 20
- 2.3.2 RAS Mode 21
- 2.4 Ethernet Interface 22
- 2.4.2 Fabric Interface 23
- 2.4.3 I/O Ethernet Interface 23
- 2.5 Zone 3 Interface (RTM) 24
- Chapter 3 26
- Installation 26
- 3.1 Processor 27
- 3.2 Memory 27
- 3.3 Console Terminal Setup 28
- 3.3.2 Terminal Emulator 32
- 3.3.3 PuTTY Configuration 33
- 3.4 Installing the MIC-5332 35
- 3.4.2 FMM (Option) 36
- 3.4.3 RTM (Optional) 39
- 3.4.4 Storage (Optional) 39
- 3.4.5 Front Panel 39
- 3.4.6 LED Definition 40
- 3.4.7 Jumper Settings 42
- JP5 JP6 43
- Chapter 4 44
- Hardware Management 44
- 4.1 Overview 45
- 4.3 Board Information 48
- 4.3 Sensors 50
- 4.3.1 Voltage Sensors 52
- 4.3.2 Thermal Sensors 53
- 4.3.3 Discrete sensors 55
- 4.3.4 Integrity Sensor 56
- 4.4 Watchdog Timers 57
- 4.5 E-Keying 58
- 4.6 Serial-over-LAN (SoL) 58
- 4.6.2 SoL Preparation 59
- 4.6.3 SoL Establishment 61
- 4.7 Dynamic Power Budgeting 66
- 4.8 MAC Address Mirroring 67
- 4.9 RTC Synchronization 68
- Chapter 5 70
- AMI APTIO BIOS Setup 70
- 5.1 Introduction 71
- 5.2 Entering Setup 71
- 5.3 Main Setup 72
- 5.4.1 PCI Subsystem Settings 75
- 5.4.4 WHEA Configuration 77
- 5.4.5 CPU Configuration 78
- 5.4.6 Runtime Error Logging 79
- Start Unit command 82
- will take before it 82
- 5.4.12 Network Stack 84
- 5.4.13 iSCSI 85
- 5.5 Chipset Setup 86
- 5.5.1 North Bridge 87
- 5.5.2 South Bridge 88
- 5.7 Boot Setup 91
- 5.8 Security Setup 92
- 5.9 Save & Exit Option 93
- Chapter 6 95
- Firmware Upgrade 95
- 6.2 IPMItool 96
- 6.3 BMC Upgrade 96
- 6.4 FPGA Upgrade 98
- 6.4.3 Payload Reset 100
- 6.5 BIOS Upgrade 101
- 6.5.1 Upload new BIOS image 102
- 6.5.3 Payload Reset 103
- 6.6 NVRAM Upgrade 104
- <section> 105
- 6.6.2 Upload new NVRAM image 106
- 6.6.4 Payload Reset 107
- Appendix A 108
- 39 28 00 114
- 39 28 00 <setting> 114
- 39 28 00 <POST Code> 117
- 39 28 00 <MAC-Address> 118
- Appendix B 119
- Appendix C 121
- Appendix D 124
- Zone 3 J32 pin out 125
- Zone 3 J34 pin out 125
- Appendix E 127
Powiązane produkty i podręczniki dla Networking Advantech MIC-5332
Networking Advantech FWA-3180 Dokumentacja
(22 strony)
(22 strony)
Polaris 2001 XCF SP Edge manuels
Manuels d'utilisation et guides de l'utilisateur pour Machines spéciales Polaris 2001 XCF SP Edge.
Nous fournissons des manuels en pdf 1 Polaris 2001 XCF SP Edge à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji