POC- 195 Pentium® M processor-based Point of Care Terminal with 19” TFT LCD User’s Manual
Figure 2-5: Connecting the power cord 2.2.2 Connecting the keyboard and mouse 1. Connect the Y-shaped adapter to the PS/2 mouse and keyboar
If required, insert your operating system's installation or setup diskette into the optical drive until the release button pops out. (See Figure
Max memory allocation support based on total system memory 1-MB or 8 MB of pre-allocated memory supported. 3.1.3 LVDS Transmitter The POC-195 uses Ch
Step 1-3 Read License Agreement and click ‘Yes’ to proceed. Step 1-4 When the 'Setup COMPLETE' message appears click 'Finish' to
Step 2-1 Click the 'Start' button in the task bar, click 'Run' and then select ‘Setup.exe’ from the drive directory “D://VGA/” w
Step 2-3 Read License Agreement and click ‘Yes’ to proceed. Step 2-4 When the 'Setup COMPLETE' message appears click 'Finish&apos
3.3 Further information For further information about the VGA installation in your POC-195, included Driver updates, troubleshooting guides and FAQ l
Note2 <Enter> means pressing the “Enter” key on the keyboard. 4.2.1 Installation for Windows 2000/XP Step 1-1 Click the 'Start' butt
Step 1-4 When the 'Setup COMPLETE' message appears click 'Finish' to restart your computer. 4.3 Further information For further
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The
Step 1-1 Click the 'Start' button in the task bar, click 'Run' and then select ' sw500930.exe' from the drive directory
Step 1-5 click 'Next' to continue. Step 1-6 Read License Agreement and click ‘Yes’ to proceed.
Step 1-7 click 'Next' to continue. Step 1-8 click 'Next' to continue.
Step 1-9 click 'Next' to continue.
Step 1-10 When the 'Setup COMPLETE' message appears click 'Finish'. And follow up the software guiding to complete touch screen c
5.3 Further information For further information about the Touchscreen installation in your POC-195, included Driver updates, troubleshooting guide
Step 1-3 click 'Next' to continue. Step 1-4 When the 'Setup COMPLETE' message appears click 'Finish' to restart
6.3 Further information For further information about the Ethernet installation in your POC-195, included Driver updates, troubleshooting guides and
Warning 1. Input voltage rated 100-240 VAC, 50-60 Hz, 4-2 A (AC Mode) 2. Use a 3 V @ 195 mA lithium battery (Model No. BR2032) 3. Packing: please c
Supply Class I adapter No applied part IPX1 Continuous Operation Not AP or APG category 19. Disconnect device: Appliance inlet. 20. Follow the nationa
Chapter 1General Information 1.1 Introduction The POC-195 is a multimedia Pentiu
• Audio controller: 18-bit codec, full-duplex stereo codec • Audio interface: Microphone-in, Line-in, Line-out • Internal Speaker: 1W speaker x 2,
Cleaning/Disinfecting During normal use of the POC-195 may become soiled and should, therefore, be cleaned regularly. Agents: Green tinctured soap and
2.1 A Quick Tour of the POC-195 Before you start to set up the POC-195, take a moment to b
A Isolated RS-232 COM port (COM1 /COM2/COM3 ) B PS/2 Mouse/Keyboard Port B IEEE-1394a Port D Parallel Port E Line-out/Line-in/MIC-in Port ( From
Komentarze do niniejszej Instrukcji