Advantech PWS-1409 Instrukcja Użytkownika Strona 1

1PWS-1409/1419 User’s ManualPWS-1419/14099-slot 14.1” TFT LCD Portable WorstationAdvantech Portable WorkstationUser’s Manual

10PWS-1409/1419 User’s Manual 1-6-1 Optional Slim FDD, CD ROMOptional Slim Floppy Disk Kit1. Floppy disk power cable2. Floppy interface board3. Flo

11PWS-1409/1419 User’s ManualThe pin out may be different for other brand or version of CD ROM & floppy diskDo not use the CD ROM and floppy fro

12PWS-1409/1419 User’s Manual 1-7-2 Side Views 1-7-2-a PWS-1419Use the photo below to identify components and I/O ports that are accessible fro

13PWS-1409/1419 User’s Manual 1-7-3 Front View 1-7-3-a PWS-1419You access the front panel controls by first disengagingthe keyboard. Disengage

14PWS-1409/1419 User’s Manual 1-7-3-b PWS-1419Push theKeyboard Latches to centerPull up the keyboard standYou access the front panel controls by

15PWS-1409/1419 User’s Manual 1-8 Detaching the Keyboard 1-8-1 PWS- 1419 1-8-1-a The Standard KeyboardThe subassembly comes with either the S

16PWS-1409/1419 User’s ManualChapter 2 PWS-1409T Construction 2-1 Opening The Chassis 17 2-1-1 Removing the Back Cover 17 2-1-2

17PWS-1409/1419 User’s Manual 2-1 Open the chassis 2-1-1 Removing the Back CoverFace the back of the chassis. Remove allscrews as shown. There are

18PWS-1409/1419 User’s Manual 2-3 Removing the CD ROM cageStep 1. Remove screws as shown (1) and then pull outthe CD ROM Upper cage.Step 2. Remove

19PWS-1409/1419 User’s Manualfind the mount point of the backplaneinsert the stand offsThread clock-wise to insert the standoffreverse to take off t

2PWS-1409/1419 User’s ManualThe information contained in this document is believed to be accurate. However, noresponsibility is assumed for its use,

20PWS-1409/1419 User’s Manual 2-7 Connecting the power ConnectorThe plug from the power supply will only insert in one orientation. Push down firm

21PWS-1409/1419 User’s Manual#1 fix interface board to CD ROM #10 fix CD ROM to CD ROM cage#6 fix CD ROM bottom cage to side of case #7 Fix CD R

22PWS-1409/1419 User’s Manual 2-9 Installing the CD ROM CageStep 1. Carefully put the drive cage back into the chassis. (fig1)Step 2. Align the s

23PWS-1409/1419 User’s Manual 2-11 Installing the hard driverThe drive cage supports one slim Floppy disk and a 3.5” Hard disk drives.Step 1. Tak

24PWS-1409/1419 User’s ManualPull up the small cage carefullyConnect the signal cableThe cable has pin 1 on the dot pointPush back the small cagePus

25PWS-1409/1419 User’s ManualStep10. Connect the signal cableStep11. Connect the power cable 2-13 Installing the Drive cage into the caseStep 1

26PWS-1409/1419 User’s Manual 2-14 Installing the SBC 2-14-1 Setting your SBC JumpersBefore installing the motherboard in the chassis, install

27PWS-1409/1419 User’s ManualConnect the signal cable and chassis cablebefore fix the SBCFix the SBC with screw #2 2-15 Installing the Add-on Car

28PWS-1409/1419 User’s ManualStep 3. Slide each clip so they come in contact with the top edge of the add-on cards.While holding the clip firmly aga

29PWS-1409/1419 User’s Manual1. Connect the VGA Connector2. Connect the input device3. Connect the other connectors for other device such a

3PWS-1409/1419 User’s Manual Chapter 2 PWS-1409 Construction 1-1 Specification

30PWS-1409/1419 User’s Manual 3-1 Opening The Chassis 31 3-1-1 Removing the Back Cover 31 3-2 Removing the Card Stabilizers 31 3-3 Identif

31PWS-1409/1419 User’s Manual Chapter 3 PWS-1409 Construction 3-1 Open the chassis 3-1-1 Removing the Back CoverFace the back of the chassis.

32PWS-1409/1419 User’s Manual 3-5 Installing The BackplaneMake sure that at no time you are working on any electrical or electronic components wh

33PWS-1409/1419 User’s Manualfind the mount point of the backplaneinsert the stand offsThread clock-wise to insert the standoffreverse to take off t

34PWS-1409/1419 User’s Manual 3-6 Connecting the power ConnectorThe plug from the power supply will only insert in one orientation. Push down fir

35PWS-1409/1419 User’s Manual secure the hard disk to drive cage with screw# 5, insert washer #3 between cage andscrew, same with the other side sec

36PWS-1409/1419 User’s Manual 3-8 Intall the driver cage to caseStep 1. Carefully put the drive cage back into the chassis.Step 2. Plugging the

37PWS-1409/1419 User’s Manual 3-9 Installing the SBC 3-9-1 Setting your SBC JumpersBefore installing the motherboard in the chassis, install t

38PWS-1409/1419 User’s ManualConnect the signal cable and chassis cablebefore fix the SBCFix the SBC with screw #2 3-10 Installing the Add-on Card

39PWS-1409/1419 User’s ManualStep 3. Slide each clip so they come in contact with the top edge of the add-on cards.While holding the clip firmly aga

4PWS-1409/1419 User’s ManualChapter 4 Using The System ControlsChapter 3 PWS-1409 Construction 2-7 Connecting the Power Connector 20 2-8 In

40PWS-1409/1419 User’s Manual1. Connect the VGA Connector2. Connect the other connectors for other device such as Ethernet, Audio device… 3-13 Clo

41PWS-1409/1419 User’s ManualChapter 4 Using The System Controls 4-1 Starting your System 42 4-1-1 Systems with ATX Power Supply 42 4-2 OSD

42PWS-1409/1419 User’s Manual Chapter 4 Using The System Controls 4-1 Starting your SystemBefore starting your system, plug in the power cord an

43PWS-1409/1419 User’s Manual CONTRAST MENUContrast: Manual adjustment the contrastSub-CONTRAST: Manual adjustment of individual RGB channel cont

44PWS-1409/1419 User’s ManualThe internal fan is the entrance of the system air flow. It may contain dust during thelong use. Change or clean the fi

45PWS-1409/1419 User’s ManualAppendix A. Trouble shooting A-1 Trouble Shooting Techniques 46 A-1-1 No screen after pressing front power switch

46PWS-1409/1419 User’s Manual A-1 Trouble Shooting Techniques A-1-1 No screen after pressing front power switchA-1-1-a Power supply fan not spinn

47PWS-1409/1419 User’s Manual A-1-3 LCD SCREEN works fine in Windows but acted funny when running certainprograms or games:The built-in Intelligen

48PWS-1409/1419 User’s ManualAppendix B: LCD VIDEO Controller B-1 Introduction 49 B-2 Safety Precautions 50 B-3Configuring Your Controller 50

49PWS-1409/1419 User’s Manual B-1 IntroductionThe LCD video controller subassembly is an “in-monitor” design build around a highperformance ASIC te

5PWS-1409/1419 User’s ManualAppendix A. Trouble shooting4-1 Starting your System 42 4-1-1 Systems with ATX Power Supply 42 4-2 OSD Controls

50PWS-1409/1419 User’s ManualThe light source for most flat panel displays is a cold cathode fluorescent backlight.These backlights run on high AC v

51PWS-1409/1419 User’s ManualFollow these steps to activate the on-screen display and make any adjustments to suityour preference:Step 1. Power up

52PWS-1409/1419 User’s Manual B-4-1-c POSITIONH-SIZE: Adjustment of the vertical image sizeCKOCK PHASE: adjustment of the ADC sample pixel clock.H.

6PWS-1409/1419 User’s Manual 1-1 Specification

7PWS-1409/1419 User’s Manual Support passive backplane form factor platforms. 14.1” High resolution color matrix TFT LCD display Built-in analog

8PWS-1409/1419 User’s Manual1-2 Before You StartThe major component of the subassembly is the chassis, which comes in two mod-els—8x ISA/ 1 CPUslot

9PWS-1409/1419 User’s Manual1-3-4 VentilationThe chassis comes with three intake fans and one power supply exhaust fan providingcooling and air flo