Advantech PCM-3350 Series Instrukcja Użytkownika

PCM-3350 SeriesNS Geode 586-Level PC/104CPU Module with SVGA/LCD/LAN InterfaceUser's Manual

CHAPTERGeneral InformationThis chapter gives background information onthe PCM-3350.Sections include:• Introduction• Features• Specifications• Board di

2 PCM-3350 User's Manual1.1 IntroductionThe PCM-3350 is the ultimate cost-effective solution for limited spaceapplications. It is a new NS Geode

Chapter 1 General Information 31.2 Features• Ultra-compact size single board computer, smaller than a 3½" harddisk drive (96 mm x 90 mm)• Onboar

4 PCM-3350 User's Manual1.3 Specifications1.3.1 Standard SBC functions• CPU:Embedded Low power NS Geode GX1-300 MHz processor• BIOS: AWARD 256 K

Chapter 1 General Information 5• CRT display mode: Non-interlaced CRT monitor resolutions up to1024 x 768 @ 24 bpp1.3.4 Ethernet function• Chipset:

6 PCM-3350 User's Manual1.4 Board dimensionsFigure 1-1: PCM-3350 dimensions

CHAPTER2InstallationThis chapter tells how to set up thePCM-3350 hardware. It includes instruc-tions on setting jumpers and connectingperipherals, swi

8 PCM-3350 User's Manual2.1 ConnectorsThe board has a number of connectors that allow you to configureyour system to suit your application.The

Chapter 2 Installation 92.2 Locating connectorsWarning: Make sure you use the correct component side.Improper installation can cause serious damage t

Copyright noticeThis document is copyrighted, 2001. All rights are reserved.The original manufacturer reserves the right to makeimprovements to the p

10 PCM-3350 User's Manual2.3 Safety precautionsWarning! Always completely disconnect the power cord fromyour board whenever you are working on i

Chapter 2 Installation 112.6 Serial ports(CN3: COM1; CN4: COM2/RS-232; CN18: COM2/RS-422/485)The PCA-3350F offers two serial ports: COM1 in RS-232 an

12 PCM-3350 User's Manualthis in the system BIOS setup. The table below shows the settings forthe PCA-3350F Series' board's ports:Tabl

Chapter 2 Installation 132.9 Parallel port connector (CN7)Normally, the parallel port is used to connect the card to a printer. ThePCM-3350 includes

14 PCM-3350 User's Manual2.13 PS/2 keyboard/mouse connector(CN12)The PCM-3350 board provides a pin head keyboard connector, whichsupports both a

Chapter 2 Installation 15pin number one should be on the right. Please refer to any documenta-tion that came with the drive for more information.If y

16 PCM-3350 User's ManualMultifunction jumpers (MJ1)MJ1-AMJ1-B MJ1-C MJ1-D MJ1-E2.17 Multifunction Jumpers (MJ1)MJ1 Assign Pins Function NotesMJ

Chapter 2 Installation 172.17.4 IR connector (MJ1-D)This connector supports the optional wireless infrared transmittingand receiving module. This mod

18 PCM-3350 User's Manual1. Make sure that all power supplies to the system are switched off.2. Install the SODIMM card. Install the SODIMM so t

Chapter 2 Installation 19

Packing listBefore you begin installing your card, please make sure that thefollowing materials have been shipped:• 1 PCM-3350 All-in-one single boa

20 PCM-3350 User's Manual

Software ConfigurationThis chapter details the software configu-ration information. It shows you how toconfigure the card to match your applica-tion r

22 PCM-3350 User's Manual3.1 IntroductionThe PCM-3350 system BIOS and custom drivers are located in a 256KB, 32-pin Flash ROM device, designated

Chapter 3 Software Configuration 231. Apply power to the PCM-3350 Series with a color TFT displayattached. This is the default setting for the PCM-33

24 PCM-3350 User's Manual3.4 Connections for two standard LCDs3.4.1 Connections for Toshiba LTM10C042(640 x 480TFT color LCD)Table 3-1: Connectio

Chapter 3 Software Configuration 253.4.2 Connections for Toshiba LTM12C275A (800 x 600 TFT color LCD)Table 3-2: Connections for Toshiba LTM12C2

26 PCM-3350 User's Manual

Award BIOS SetupThis chapter describes how to set BIOSconfiguration data.CHAPTER4

28 PCM-3350 User's Manual4.1 System test and initializationThese routines test and initialize board hardware. If the routinesencounter an error

Chapter 4 Award BIOS Setup 294.2 Award BIOS setupAward’s BIOS ROM has a built-in Setup program that allows usersto modify the basic system configurat

ContentsChapter 1 General Information 11.1 Introduction... 21.2 Features ...

30 PCM-3350 User's Manual4.2.2 Standard CMOS setupWhen you choose the STANDARD CMOS SETUP option from theINITIAL SETUP SCREEN menu, the screen s

Chapter 4 Award BIOS Setup 314.2.3 BIOS features setupBy choosing the BIOS FEATURES SETUP option from the INITIALSETUP SCREEN menu, the screen below

32 PCM-3350 User's Manual4.2.4 Chipset features setupBy choosing the CHIPSET FEATURES SETUP option from theINITIAL SETUP SCREEN menu, the screen

Chapter 4 Award BIOS Setup 334.2.5 Power management setupBy choosing the POWER MANAGEMENT SETUP option from theINITIAL SETUP SCREEN menu, the screen

34 PCM-3350 User's Manual4.2.6 PnP/PCI configurationBy choosing the PnP/PCI CONFIGURATION option from the InitialSetup Screen menu, the screen b

Chapter 4 Award BIOS Setup 354.2.7 Integrated peripheralsBy choosing the INTEGRATED PERIPHERALS option from theINITIAL SETUP SCREEN menu, the screen

36 PCM-3350 User's Manual4.2.8 Change passwordTo change the password, choose the PASSWORD SETTINGoption form the Setup main menu and press <E

Chapter 4 Award BIOS Setup 374.2.9 Save & exit setupIf you select this option and press <Enter>, the values entered inthe setup utilities w

38 PCM-3350 User's Manual

PCI Bus EthernetInterfaceThis chapter provides information onEthernet configuration.• Introduction• Installation of Ethernet driver forWindows 98/NT/2

2.11 VGA connector (CN9) ... 132.11.1 CRT display connector (CN9) ... 13

40 PCM-3350 User's Manual5.1 IntroductionThe PCM-3350 is equipped with a high performance 32-bit Ethernetchipset which is fully compliant with I

Chapter 5 PCI Bus Ethernet Interface 411. a. Select "Start", "Settings". "Control Panel".b. Double click "Network&

42 PCM-3350 User's Manual3. a. Select the "Adapter" item to add the Ethernet card.4. a. Click "Have Disk" to install the dri

Chapter 5 PCI Bus Ethernet Interface 436. a. Choose the "82559ER" item.b. Click "OK".7. a. Make sure the configurations of relati

44 PCM-3350 User's Manual5.3 Further informationRealtek website: www.Realtek.comEMAC website:www.emacinc.com

SVGA Setup• Introduction• Installation of SVGA driver for Win-dows 95/98/NTCHAPTER6

46 PCM-3350 User's Manual6.1 IntroductionThe PCM-3350 Series has an on-board LCD/VGA interface. Thespecifications and features are described as f

Chapter 6 SVGA Setup 476.2.1 Installation for Cyrix MediaGX Certified driversfor Windows 95/98. Insert the disk into the CD-ROMdrive.1. Select "

48 PCM-3350 User's Manual2. Click "Finish" to continue.3. Click "Next" to proceed to the next step. Click "Yes" aft

Chapter 6 SVGA Setup 494. Follow the instructions which appear on the screen.5. Insert the Win95/ 98 CD-ROM into the CD-ROM drive. Type the correctpa

4.2.5 Power management setup ... 334.2.6 PnP/PCI configuration ... 34

50 PCM-3350 User's Manual6. Choose "Yes", then click "Finish" to restart the computer.

Chapter 6 SVGA Setup 516.2.2 Installation for Windows NT1. a. Select "Start", "Settings" then "Control Panel" to get to

52 PCM-3350 User's Manual3.Press the "Change..." button.4. Click on the "Have Disk..." button

Chapter 6 SVGA Setup 535. a. Insert the disk into the CD-ROM drive.b. Type "D:\PC104\3350\VGA\WINNT\VGA.110\"c. Press "OK".6. a.

54 PCM-3350 User's Manual7. Press "Yes" to proceed.8. Press "OK" to reboot.

Chapter 6 SVGA Setup 559. a. Repeat Step 1 in this manual, select the "Settings" label.b. Adjust the resolution and color.c. Click "Te

56 PCM-3350 User's Manual6.3 Further informationFor further information about the PCI/SVGA installation in yourPCM-3350, including driver updates

Programming theWatchdog TimerThe PCM-3350 is equipped with awatchdog timer that resets the CPU orgenerates an interrupt if processing comesto a stands

58 PCM-3350 User's ManualA.1 Programming the watchdog timerThe default configuration of the timer is enabled with system reset.To enable the wat

Appendix A Programming the Watchdog Timer 59The following example shows how you might program the watchdogtimer in BASIC:10 REM Watchdog timer examp

C.6 PC/104 connector (CN6) ... 70C.7 Parallel port connector (CN7) ...

60 PCM-3350 User's Manual

APPENDIXBInstalling PC/104ModulesThis appendix gives instructions forinstalling PC/104 modules.

62 PCM-3350 User's ManualB.1 Installing PC/104 modulesThe PCM-3350's PC/104 connectors give you the flexibility to attachPC/104 modules.Ins

Appendix B Installing PC/104 Modules 63Figure B-1: PC/104 module mounting diagramFigure B-2: PC/104 module dimensions (mm) (±0.1)PCM-3346FemalePC/104

64 PCM-3350 User's ManualTable B-1: PCM-3350 PC/104 connectors (CN6)Pin Signal (CN6) Signal (CN6)Number Row A Row B Row C Row D0— — 0 V0 V1 IOCH

Pin AssignmentsThis appendix contains information of adetailed or specialized nature. It includes:• Ethernet connector• LCD connector• COM1 connector•

66 PCM-3350 User's ManualC.1 Ethernet connector (CN1)Table C-1: Ethernet connector (CN1)Pin Signal Pin Signal1 Vcc (+5 V) 2 ACTLED-3 RX+ 4 RX-5

Appendix C Pin Assignments 67C.2 LCD connector (CN2)Table C-2: LCD connector (CN2)Pin Signal Pin Signal1 VDDSAFE +5 V 2 VDDSAFE +5 V3 GND 4 GND5 VDDS

68 PCM-3350 User's ManualC.3 COM1 connector (CN3)Table C-3: COM1 connector (CN3)Pin Signal Pin Signal1 RLSD 2 DSR3 RX 4 RTS5 TX 6 CTS7 DTR 8 RI9

Appendix C Pin Assignments 69C.5 EIDE hard drive connector (CN5)Table C-5: EIDE hard drive connector (CN5)Pin Signal Pin Signal1 *RESET 2 GND3D7 4D85

FiguresFigure 1-1: PCM-3350 dimensions ... 6Figure 2-1: Locating connectors (component si

70 PCM-3350 User's ManualC.6 PC/104 connector (CN6)For details on PC/104 connectors, please refer to Appendix B.C.7 Parallel port connector (CN7

Appendix C Pin Assignments 71C.8 Backlight connector (CN8)C.9 VGA connector (CN9)Table C-9: VGA connector (CN11)Pin Signal Pin Signal1 RED_OUT 2 VCC_

72 PCM-3350 User's ManualC.10 Main power (+5 V) connector (CN11)Table C-10: Main power (+5 V) connector (CN11)Pin Signal1 +12 V2 GND3 GND4 Vcc (

Appendix C Pin Assignments 73C.12 FDD connector (CN14)Table C-12: FDD connector (CN14)Pin Signal1 Vcc (5 V)2 INDEX3 Vcc (5 V)4 DRIVE SELECT 05 Vcc (5

8712C.13 USB connector (CN17)Table C-13: USB connectorPin Signal Pin Signal1 USBVCC (5 V) 2 USB VCC (5 V)3 DATA 0- 4 DATA 1-5 DATA 0+ 6 DATA 1

74 PCM-3350 User's ManualC.13CompactFlash™ socket (CN16)Table C-13: CompactFlash™ socket (CN16)Pin Signal Pin Signal1 GND 2 D033 D04 4 D055 D06

Appendix C Pin Assignments 75Figure C-1: CompactFlash™ socket

76 PCM-3350 User's ManualC.14 COM2 connector for 422/485 (CN18)Table C-15: MJ1-A, -5 V, -12 V inputPin Signal1 -5 V2 GND3 -12 VTable C-16: MJ1-B

Appendix C Pin Assignments 77Table C-17: MJ1-C, reset buttonPin Signal9 *system reset10 GNDTable C-18: MJ1-D, IR connectorPin Signal12 +5 V13 NC14 Re

78 PCM-3350 User's Manual

TablesTable 2-1: Connectors ... 8Table 2-2: Serial

System Assignments• System I/O ports• DMA channel assignments• Interrupt assignments• 1st MB memory mapAPPENDIXD

80 PCM-3350 User's ManualD.1 System I/O portsTable D-1: System I/O portsAddr. range(Hex) Device000-01F DMA controller020-021 Interrupt controller

Appendix D System Assignments 81D.2 DMA channel assignmentsTable D-2: DMA channel assignmentsChannel Function0 Available1 Available2 Floppy disk (8-bi

82 PCM-3350 User's ManualD.3 Interrupt assignmentsTable D-3: Interrupt assignmentsInterrupt# Interrupt sourceNMI Parity error detectedIRQ 0 Inter

Appendix D System Assignments 83D.4 1st MB memory mapTable D-4: 1st MB memory mapAddr. range (Hex) DeviceF000h - FFFFh System ROME000 - EFFF UnusedCC0